-
Separate Ground Connection and Layout Power Components
Mortensen 05/25/2016 4.5 4.5/5 (2 ) -
Pspice Simulation of 1x and 10x Probes and Waveform Distortion
anaya.rangan 03/27/2016 -
A DDR3 PCB Design Case Study
Mortensen 04/15/2016 -
Diplexer and Tx/Rx Isolation
ManishaSnoyer 01/20/2016 -
New DRAM access technology doubled overclocking performance
Mortensen 01/27/2018 -
[Tool] PCB Via Capacitance and Inductance
Mortensen 08/01/2016 4.6 4.6/5 (5 ) -
What are some semiconductor devices?
shenzhengrande 08/06/2019 -
Digital Design Interiew Questions with Answers
MattChiu 03/02/2016 -
How Long an Input Pad Needs to be Asserted for a Chip to See it?
SJean 03/02/2020 -
Display Eye Diagram in Pspice V
KSen 08/04/2016 4 4/5 (1 )
-
Some PCB EMI Guidelines Learned out of My Previous Projects
Mortensen 04/07/2016 5 5/5 (1 )
-
PCB/EMI Expert with 8+ Years of Experience
Mortensen 04/07/2016$30
-
High Speed Digital Design Two-Day Workshop Handout
vonk 04/01/2016$30
-
Xilinx FPGA and TI DSP communication fails at low temperature,
-
Any online component library,
-
Your most weird board design issue,
What software do you use to simulate signal integrity of PCB?
Which software you use to sim SI?
- Mentor Graphic Hyperlynx
- Spice tools such as Pspice, Hspice, and LTspice
- Ansoft Siwave
- Eagle Simulator
- Tina Tools
- Others (please specify it in comments)
Maximum 0 options allowed
>> Login to vote-
What software do you use to simulate signal integrity of PCB?
Start: 04/08/2016
Comments: 0
No polls to show
Topics
-
QUCS, open source circuit simuator
morris119 08/01/2016 -
[Book] Analog Device (ADI) Op Amp Handbook
anaya.rangan 04/15/2016 -
[Whitepaper] Mentor Graphic DDR4 Board Design and Signal Integrity Verification Challenges
VinayClark 04/16/2016 4 4/5 (1 ) -
How to Carry Out Prototype Manufacturing
Pcb manufacturing 09/24/2019 -
Williamson Labs for Hardware Designers
abazzi 03/11/2016 -
Articles and Blogs of Dr. Howard Johnson on High Speed Digital Design
vonk 04/01/2016 5 5/5 (2 )
[1-hour webinar] MEMS-based sensors for high-performance environmental monitoring
http://m.events.st.com/nl/jsp/m.jsp?c=%40j4Vo0BwublyTuhEPDneprXEl3I4KeCnIdEQK4ljv1Nw%3D&cid=stmDM24263&bid=260533699&uid=gqQdyC0TEiLNC54i8nMAVO0+UhyHejoc
Use #FCBGA package to mount and test a #die
Not many, actually only a few, may have this issue. You get the die back but it is not packaged yet. How to put it on pcb board to test?
In old days, a small pcb board is designed. Mount die on this small board and then mount the latter on the…[Read more]
#Crystal osc circuit chip internal drive strength adjust
A typical #xtal osc is shown. Two caps and xtal are external to chip. The op amp is inside chip. To board designers, that op amp driving strength is not fixed. They normally have higher driving strength at bootup to make sure xtal…[Read more]
Another reason to use 3.3k-10k for pull up
3.3-10k is normally used for pull up. Main reason is RC rise time. Another consideration is chip internal pull up/down. They are normally around 50k but with big variation. Sure they can be turned off later by fw to avoid conflict of board pull…[Read more]
TI Releases USB Type-C Reference Design
[Read more]
[Video] Use MG Hyperlynx for board power integrity and thermal simulation
Short 6 minute video and right on the point. It shows how easy to analyze thermal and power integrity issue such as current density and their effects on board temp distribution.
[Read more]
IO Pad Checking with IV Curve
Debugged a chip and one of its IO was not functioning. We suspected IO pad might be burned. So we used IV curve tracer to get this IO’s IV curve. It came back as the graph shown. Turned out this kind of waveform was expected. The ESD protection window defines…[Read more]
A short video demo about using HyperLynx to analyze SI and COM of multi-Gb/s serial channel
Doing high speed board design these days. See this video online. Though it could be useful to others too.
[Read more]